nyne wood floors band-it details

Building the Nyne House Part 4: Main Room Flooring

This is going to be a long post with lots of pictures.

While it is still work on the Nyne, this is largely an experiment/how-to-guide using Band-It wood veneer strips, wood filler, and wood stain.

Measuring out the Main Room floor on the Nyne House

When conceptualizing the Nyne, my initial idea was to have the floors be removable. To plan for that, I cut out the exact surface of the floors where I will be adding the wood material to. In retrospect, its probably not going to be removable.. that would be too much for a first scratch build, I think.

Using Band-It for the floors

I had thought about using some leftover ply as the surface, but I opted to use cardboard instead because I had planned on using Band-It, birch veneer edging strips.

An Iron and a pair of scissors was all I needed to apply the Band-it strips.

The Band-It comes pre-glued on the back to be applied by using an ordinary iron. The glue is essentially hot glue, so I was not worried about warping the cardboard, as I would if I used wood glue. Even better is the fact that I can cut it with a pair of scissors. No complicated tools or set up, Xacto knives, or cutting mat needed.

Applying the strips More in progress photos

Some work in progress pics above.

Warping of the birch stripwood

I ran out of strips and had to get more from HomeDepot. After getting back, I turned on the iron to finish up but did not pay attention to the settings. The iron was set to steam, so it warped the sides of the birch strips with just a single gush of steam from the iron. Attempts to repair it seemed to make it worse. *grumbles*

On the bright side, I figured that the warped part will be largely covered by an area rug, so its ok!

Using wood filler

Band-It strips are not cut perfectly strait, nor did I apply them perfectly strait, so there will be gaps. My brilliant fix-it idea was to use wood filler to make the gaps less noticeable.

Being the dolt that I am, I didn’t get the LIGHTER filler color, so it looks quite funky on the lighter birch. I wasn’t kicking myself too bad on this because I had decided early on to stain the floors an espresso/ebony color:

Espresso stained wood floors

Doesn’t that just look sexy? (source)

The darker stain will really help hide the mistakes and the gaps.

Minwax wood stain

I played it cheap and just went with the darkest stain that I had on hand.

Some problems with the veneer strips

The color is too red for me and I don’t think more applications of the stain will help. It will just have the same color as the bottom right most part of the image above and I would rather have a deep, dark brown, almost black color. This means I’ll be making another trip to HomeDepot.

You can see my sloppy wood filling job in the picture, but its not very noticeable from afar.

You may have already spot the other mistake. There are jagged edges in the middle of a few strips. I didn’t notice them when I was applying the Band-It (I was watching TV :-().

I am stuck with this mistake since there isn’t much I can do to fix it. The jagged strips are spread fairly evenly throughout the floors, so I’ll just say that its a decorative element and I meant to do it!

Possible Kitchen floor for the Nyne House

Lastly, I have a possible kitchen floor for the Nyne House. It’s a lovely color with an iridescent sheen to parts of it. I rather like it, but I don’t think it would look well with the main floor color. I think something darker and marble-y will work better?

Hmm..

, , , , , , , ,

5 Responses to Building the Nyne House Part 4: Main Room Flooring

  1. Lyssa December 1, 2010 at 12:44 pm #

    What a trial! Miniwax has a really nice walnut color that should yield the results you are looking for. I know you strive for perfection, but it still doesn’t look bad. Not for a first attempt using those strips. I have seen some beautiful applications of them, but they are certainly harder to use than one would think. =)

    • Ann December 1, 2010 at 8:34 pm #

      I do hate being a perfectionist sometimes. I end up aggravating myself! And I agree, its not as easy using the strips as I thought.. my fingers were all red from the iron after applying them! It was a good learning experience and I’m looking forward to using them in future projects.

  2. Melissa Johnson December 16, 2010 at 7:29 pm #

    Great idea! I can’t stand using the pre-made wood flooring from the dollhouse store…it always warps on me. Using peel and stick tile has worked quite well for me. I buy the cheapest ones at the hardware store, cut them on a heavy duty paper cutter into either one inch squares (grout or not grout) or “wood” strips and just stick them down. Looks real. Thanks for another idea of how to do wood floors!

    • Ann December 16, 2010 at 8:14 pm #

      You’re very welcome Melissa! Working with the veneer strips will give pink fingers from the iron, but its so worth it. And I agree, it looks real enough for minis. When you do try it out, so share some photos!

      Also, hardware stores as a source for miniature building materials is one of the best kept secret and I’m glad to see more people using it as a source for minis 😀

  3. Ann December 16, 2010 at 8:13 pm #

    You’re very welcome Melissa! Working with the veneer strips will give pink fingers from the iron, but I agree, it looks real enough for me. 😉 When you do try it out, so share some photos!

    Also, hardware stores as a source for miniature building materials is one of the best kept secret.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Copyright 2009 - 2015 Ann Nguyen & AmazingMiniatures.com